How To Use Leather Repair Kit

READ INSTRUCTIONS BEFORE STARTING

BEFORE /AFTER

.

.

.

.

.

"SELECT THE REPAIR PROCEDURE"

.

.

A) Seat panel or complete seat needs re-coloring. Leather or vinyl is in good shape. No cuts, holes or punctures.
May take some light scratches or light cracks in the leather surface.

.

.

.

B) Cuts, holes or punctures that get all the way through the leather or vinyl that exposes the foam padding underneath.

.

Step one: Gear up-Up

1) Additional items (not provided) that may be needed:

Paper or material towels - Masking tape - Scissors - Hair dryer (a must to assist dry the color and the repair products).
Utilize newspaper, drop textile or paper-thin to cover everything that is not to be repaired or re-colored.
Including carpet, kick panels, center consoles, seat belts, wooden legs, etc.
2) Wear the gloves provided during the entire process.
3) Total time required to consummate most boilerplate jobs volition be ane to 2 hours.
4) Seats tin can be removed from the vehicle - but it is not necessary.
5) Place work materials in close proximity to work area.

Footstep 2: COLOR Friction match

ane) Ever check the colour lucifer earlier starting. If the color is non close plenty, the repair will not expect correct.
two) Be certain to check the colour friction match by applying a minor amount to an inconspicuous area on the particular earlier applying it to the entire particular. Utilize a few coats of color and dry completely. Apply the hair dryer to speed drying time. Remove the test color immediately with the triclean cleaner.
3) Check the color match in the viewing light. Auto seat color should be viewed in sunlight. Furniture color should exist viewed in incandescent or fluorescent lighting.

STEP 3: CLEANING & PREPPING SURFACE

Annotation: A consummate, thorough prep cleaning of the cloth is the key to successful results in the repair and re-coloring process.
Proper training of the surface will insure maximum adhesion and immovability of all products. Most all surfaces are protected past coats of anti-adherent products that must be removed before proceeding with the coloring process. Always employ make clean lint free towels or newspaper towels.

one) Using the aerosol Triclean Prep Cleaner provided, spray the surface to be repaired then clean with the scrub pad provided.
2) With the surface still wet, utilize a newspaper towel to dry out and remove dirt, silicone, body oils, conditioners and other contaminants.
3) It'due south best to clean and color a complete panel (seam to seam) to blend the color. Some of the original color may exist removed during cleaning.
4) Clean again with a paper towel and the Triclean prep cleaner over the entire surface area to remove whatever backlog balance.

Keep to step half dozen " APPLYING Color" if repairs are not necessary.

STEP 4: Modest REPAIRS

4a) Repairing Surface Cracks or Creases

NOTE: Since most surface cracks are the original colour coat that is slap-up and not the leather or vinyl itself, sanding (smoothing) the surface is necessary.

one) Moisture the sandpaper (provided) with the Triclean Prep Cleaner and lightly wet sand the cracked or pucker surface. This will shine any rough or jagged edges. Sand downwardly to bare leather if needed. It's best to work a complete panel (seam to seam) to alloy the color.
DO NOT SAND THE SEAMS (where the threads are showing).

2) Clean once more with a paper towel and the Triclean prep cleaner over the entire sanded surface area to remove backlog remainder.
Allow the surface to dry before proceeding. Drying time may be accelerated with a hair dryer.

Note: If the surface is now shine with no cracks in the surface itself, PROCEED to STEP six

"Applying Color".

4b) Apply Repair Compound Putty to Light Cracks, Nicks or Imperfections That Are Withal in the Surface

Later sanding, the leather or vinyl surface even so has a slight crack, nick or imperfection that goes into the surface but does non become all the way through. A repair compound is required to fill the level of the repair. Utilise the hair dryer to dry repair compound.

3) Remove whatever frayed leather or vinyl edges with nail clippers or scissors.
4) Applying the repair chemical compound is a very important office of a quality repair. How advisedly the repair compound is spread over the damaged area will determine the finished look.
5) Utilise the repair compound just in the damaged surface area with the spatula. Utilize the hair dryer to speed drying. (air dry will take at least xx minutes). DO Non Effort TO FILL THE DAMAGED Area IN One LAYER! Several layers brand a stronger repair and it takes less fourth dimension to dry.
6) Utilise a second layer of repair compound, simply across the edges (over lapping virtually 1/2") of the first layer. Continue to apply repair compound in sparse coats. Use pilus dryer to dry out between layers every bit needed.
vii) The repair compound should only be practical to an area non to exceed approx. i" beyond the repair area.
viii) When the repair is level with the surface, Keep to Footstep half dozen "Applying Color".

The drying time required for the repair chemical compound will vary due to temperature, humidity and weather condition conditions.
Wipe the excess repair compound off of the spatula between each use.
Proceed the pilus dryer approx. 12 inches from the surface.

TIP: When spreading the repair compound using the spatula, proceed the blade at a 45-degree angle. Brainstorm the stroke slightly alee of the area that you lot wish to repair. With light even pressure, drag the repair compound over the damaged area. Too much pressure on the blade will cause the compound to be pushed out; as well little pressure will create distinctive edges where the compound stops.
To smoothen the repair compound, lightly wet your finger with water and smoothen the repair compound earlier it dries. After the repair compound dries, utilize the triclean to smooth the repair compound. Also lite sanding is an selection.

TIP: For damage acquired by pet claws, use the adhesive to glue down the flap of leather to the backing or cutting it off. So follow Pace (4b).

Note: If in that location are imperfections in the leather later on applying color, additional repair compound Pace (4b) can all the same be used.

Pace 5: HOLES - RIPS - CUTS

Sub-patch Material

When the damage consists of a pigsty, rip or cut in the leather or vinyl, a sub-patch material is glued underneath to reinforce and add strength to the repaired area.

1) Use precipitous scissors to cut any crude edges from inside the repair. Avoid making the hole or cutting any larger than necessary.
2) Cut a piece of sub-patch material (provided) at least 1/two" bore larger than the hole.
3) Replace any missing foam (cotton assurance tin be used) to level out the repair expanse.
4) Using the spatula or a pair of tweezers, push button the sub-patch material under the leather/vinyl. Be sure that the sub-patch is between the leather or vinyl and the cream padding underneath. Heart the sub-patch material so that information technology is centered in all directions under the hole.
5) Open the canteen of Adhesive provided, place the nozzle between the sub-patch textile and the leather and squeeze out small amounts of adhesive. Be certain that all areas of the sub-patch material are glued to the underside of the leather. The spatula tin be used to spread out the adhesive. Exist sure to clean the spatula with the Triclean after using.
6) Dry completely to ensure maximum sub-patch adhesion (xv to 20 minutes) or employ hair dryer to accelerate dry time.

TIP: Utilise light pressure with your hand, a phone book or masking tape; to hold the two pieces together until the edges are dry and bonded. Check adhesion by lightly pulling on the edges.
TIP: Remove any Adhesive from the peak of the leather or vinyl with the Triclean.

7) To finish the repair - PROCEED to Step 4b) "Apply Repair Chemical compound"- follow the instructions

Step vi: APPLYING Colour

i) Be sure to cheque the color lucifer.
ii) Embrace the surrounding piece of work area with drop cloths, newspaper or cardboard to prevent overspray or spills onto other areas.
three) Shake colour well.
4) Color should be applied in several light coats - NOT ONE THICK COAT! The least amount of colour used produces a much better finish and volition last longer.

Droplets SPRAY COLOR:
5) Follow directions on the back of the aerosol colour can.
Spraying light color coats are better than heavier color coats. The less corporeality of color applied, the amend. Ever dry betwixt coats. Do spraying the color on a sheet of paper or cardboard.

FOAM BRUSH APPLICATION:
5) Carefully remove the cap from the bottle and pour a small-scale amount of Color into the plastic paint cup that came with your kit. Replace the cap on the bottle of Color.
6) Dip the foam brush into the Color, wetting only near the first 1/2 inch. Wipe the excess on the edge of the pigment loving cup. Less color on foam castor will provide better results.
seven) Apply a thin color glaze to all repaired areas offset, do not try to achieve good color coverage. Apply the colour with smoothen, even strokes. If bubbling or runs appear in practical color, use the foam brush to even out the color before drying.
8) Let the colour coat to completely dry to affect (nearly 15-20 minutes) before applying a second glaze, it should feel polish to the touch and non tacky when dry out. Use the hair dryer to speed dry time. Don't be alarmed if the color is streaked, additional color coats will even out the color.
9) Apply a second color coat in the same manner as the start. Apply a third color coat or as many color coat's as necessary to blend in the surrounding area; thus making the repair less noticeable.

Do not let foam brush dry out with the colour on it. Continuously clean brush with h2o and dry with towel to insure softness and flexibility.

TIP: When applying colour in cold conditions, always warm the leather or vinyl earlier applying first color coat. Use a hair drier to dry out the colour between coats.
TIP: When applying color in hot conditions, always cool the leather or vinyl before applying beginning color coat. Color may dry also fast and streak when practical. Cool leather to room temperature using automobile air conditioning or a damp textile.

Annotation: Color completely cures in 24 hours. You can use the particular that has been repaired within ii hours, just exist actress careful with it. This besides applies to seating surfaces.
Articulate Coat: If the Clear Coat was purchased, apply it using the technique as above. This volition be the final glaze.

Step vii: CLEAN UP

Overspray: If there is over-spray on anything, simply wipe information technology off before drying. If information technology has dried, endeavor using the Triclean to remove it.

Make clean Up: The color used in this kit is water based and may be cleaned by ways of lather and h2o. Triclean or rubbing alcohol (not supplied) may as well be used for cleaning application equipment. For the showtime couple of hours, clean-upwardly will exist relatively easy. After 24 hours clean-up volition be extremely difficult. Wash foam brushes in warm water and liquid soap.

Stride 8: Workout

Leather is a natural product that wears and ages with time. This results in less flexibility and surface cracks. Just similar with man skin, proper maintenance and care is essential. The conditioning treatment required will depend on the state of the material.

After re-coloring, treat the leather with (ProC) Leather Conditioner. This feeds, protects and prolongs the life of the leather. Retrieve to apply a minimum of twice annually to assistance avert cracks and further harm.

one) Permit the Color to completely dry (allow 24 hours), so apply ProC Leather Conditioner with a soft towel over on the unabridged surface area. Allow to dry. Buff lightly with a clean soft cloth.
2) Employ the Leather Cleaner/Conditioner for daily or weekly ongoing maintenance and protection of leather.
iii) Use the ProC Leather Conditioner on all leather seating at least twice a yr for deep penetration of fine natural oils.

Notation: Apply caution for the first 24 hours, the new color finish may exist damaged by liquids, chemicals or heavy wear. Afterwards the 24-hour cure time, the new color coat has accomplished maximum functioning levels and durability.

Finished seat

Source: https://www.classicdyeproducts.com/_inch_leather_repair_kit_inch_instructions

Share this post